Add New Ledger to Ledger Live App Catalog and Manage Device Storage

How to Add a New Ledger App in Ledger Live requires opening the companion desktop or mobile software, connecting the hardware signer by USB or Bluetooth, depending on the model, and choosing the coin-specific module from the Manager section. Confirm the device screen prompt before installation finishes. This process writes only the currency-specific code onto the secure element, while the recovery phrase and private keys stay inside the chip and never leave it.

Before provisioning another module, check the free space reported for the secure element. Each installation consumes device memory; when capacity is tight, remove an unused coin-specific module through the same Manager section rather than deleting accounts from the companion interface. The hardware signer and the companion software must recognize each other, but the exact firmware release and supported assets are listed on the official support pages, not fixed here.

Use only the official download source for the companion software, verify the module name on the hardware signer’s screen against the listing shown in the Manager, and keep the recovery phrase offline. Third-party downloads, remote-access tools, or anyone requesting the 24 words create the main risk during installation. If the module does not appear, reconnect the device directly, restart the companion interface, and consult official support for troubleshooting.

Accounts and balances remain visible in the companion software, yet spending still requires physical approval on the device screen. Installation does not move funds, does not expose keys, and cannot be completed by a web page alone.

Check Ledger Live Version and Device Firmware Before Installing an App

Open the About panel inside the companion console and note the exact build string shown there, then line it up against the release notes published on the manufacturer’s official page before touching the manager. A plugin compiled against a later interface will not launch on an older console, and a forced push can abort midway, leaving a half-written package on the signer. Pair the hardware, unlock it with the PIN, and let the manager enumerate the device; if the install control stays grayed out, the build mismatch deserves attention before any cable swap.

Firmware comes first: a unit running older internal code rejects plugins that depend on later cryptographic instructions.

Reading the firmware build on the hardware

Unlock the device, then walk through Settings, General, and Firmware version – on touchscreen models the same line hides behind the gear icon. Write that string down and compare it with the minimum stated on the plugin’s detail card inside the manager, because that card defines the floor and the manager enforces it. Confirm the genuine check result on the same screen as well, since an unverified secure element should not be trusted to run any module at all.

Connection checks that change the outcome

Use the supplied cable in a rear USB port, or keep a Bluetooth variant within arm’s reach, and close every competing wallet program, because two processes fighting over one HID interface will simply report a disconnected device.

When either the console or the firmware sits below the required floor, update the firmware before anything else, verify the recovery phrase is written on paper and stored offline, and never type those twenty-four words into a computer, a chat, or a web form – no legitimate technician ever asks for them. Fetch the management software only from the vendor’s official domain, and treat any mirror, forum link, or sponsored search result as hostile. Exact version floors, current steps, and release history belong to the official support pages, since those values shift with each build.

Connect and Unlock Your Ledger Device for App Installation

Connect the device directly with the supplied cable, then enter the PIN on its screen.

A charge-only cable, a passive hub, or an inactive Bluetooth toggle will prevent the companion dashboard from seeing the signer. Swap to a direct port, restart the desktop software, and press a device button to keep the display awake before retrying.

After authentication, open the manager section and leave the dashboard visible; the desktop or mobile interface sends a network-specific module to the secure element, and every write must be physically confirmed on the device display. Each module occupies separate storage, so deleting one later frees space without touching the master seed, and the manager will show a progress bar until the transfer finishes.

Never enter the recovery phrase into any dashboard.

If the connection drops mid-install, reconnect the signer, re-enter the PIN on the device, and let the manager retry the write; an incomplete module can usually be overwritten, but a firmware mismatch may require a full refresh. Confirm the on-screen success message before closing the companion, and keep the cable or wireless session stable until that point.

Once the module is listed as installed, disconnect the device or end the wireless session, then reopen the manager only for another component. This reduces exposure, saves battery, and prevents accidental confirmations. For repeat detection faults, use the manufacturer’s support pages and never share the PIN or recovery words.

Open the Manager Tab in Ledger Live

Open the Manager Tab in Ledger Live after connecting the hardware wallet, entering its PIN on the device itself, and launching the desktop or mobile companion; the tab reads the device and lists installable programs. Use a data-capable cable for desktop or a paired Bluetooth link for mobile. If the tab does not populate, close the companion, reconnect the device, and confirm the connection prompt on the hardware screen.

What the Manager Tab Shows

Device state Manager tab result Check
Connected, PIN entered Shows installed and installable programs Confirm the trust prompt on the hardware screen
Locked or PIN pending Requests PIN before reading storage Type the PIN only on the device
Desktop USB Reads device storage and firmware condition Use a cable known to carry data
Mobile Bluetooth Pairs before listing programs Match the pairing code on both screens

If the tab stays blank or asks for a PIN again, verify the cable, the Bluetooth pairing, and the device screen prompt before changing settings. The Manager tab cannot move private keys; it only prepares program installation. A missing list usually means the companion cannot read the device, not that the hardware wallet is faulty. Consult the official support pages for device-specific fixes.

Safety Checks Before Installing Programs

Install only programs you recognize, and confirm every installation on the hardware wallet screen; the secure element keeps private keys inside the chip, and the companion never receives them. After installation, the program list refreshes from the device, so a repeated prompt means the connection dropped. For firmware-related limits, use the official release notes and support documentation, since supported networks, program availability, and signing requirements can change. Reject any request for the 24-word recovery phrase, whether it shows inside the companion, by email, or by phone; the Manager tab never asks for it.

Search for the App You Want to Add in the App Catalog

Type the exact ticker or full asset name into the catalog search field, then press Enter.

Match the result against the issuer or protocol listed in its description, because tickers repeat across unrelated blockchains.

Open the entry’s details pane to confirm the supported device models, the required firmware generation, and the storage footprint before installation.

If the catalog offers categories such as assets, networks, or device utilities, use the filter that matches your goal rather than scrolling the full list.

Verify the publisher field: official modules list the manufacturer or a known protocol team, while copycat entries may use similar names and misspellings.

When several matches surface, sort by name or developer and read the short summary; a legitimate listing explains which blockchain it serves, which account type it creates, and whether it needs a companion plugin.

Select the module only after checking that your hardware wallet has enough free secure-element space; installing too many network clients can force removal of another module later.

After selection, the companion suite prepares the installation and your device screen displays the final confirmation; reject any prompt that does not match the catalog name you chose.

Install a Ledger App and Confirm the Operation on Your Device

Connect the hardware wallet, unlock it with the PIN, open the companion suite, choose the asset-specific module from the catalog, and confirm the installation on the device screen.

The installation prompt is displayed on the hardware wallet’s display, not in the desktop or mobile interface. Use the physical buttons to accept or reject; the secure element chip generates and stores private keys, so the companion program never receives them. If the prompt does not show, check the USB or Bluetooth connection, unlock the device, close other management windows, and confirm the firmware is current before retrying. After the module is present, the companion suite can prepare accounts and transactions, but every address and amount must be verified on the device screen before confirmation.

Treat confirmation as a two-part check: first, the hardware wallet shows the name of the software package and asks for authorization; second, when the companion suite requests a receiving address or a signed transaction, the same screen displays the full address, the network, and the amount. Compare those details with what the desktop or mobile interface shows. Reject any mismatch, regardless of its ordinary look, because a correct installation alone does not protect against a compromised computer or phone. Remove the module only from the device’s own settings or the companion manager, and never share the recovery phrase with anyone; official support staff never ask for those 24 words. If installation stalls, disconnect, restart the companion program, reconnect the hardware wallet, and consult the manufacturer’s official support pages for fixes rather than third-party download mirrors.

Update an Existing Ledger App Instead of Reinstalling It

Use the manager pane in the companion console to refresh the installed coin-specific module; do not uninstall it first.

Connect the physical signer, unlock it, open the management suite, select the installed token handler, and choose the update control. The suite checks the package against the vendor-signed release and replaces it in place. Account labels, addresses, and histories remain in the host software because they are derived from public blockchain data and stored separately from the device module. Private keys never leave the secure element; only signed operations cross the link.

A direct refresh preserves device storage layout and avoids repeated installation prompts. Removing the module first can force you to set module-specific preferences again, such as blind signing toggles or custom derivation paths, and may leave a temporary gap until the package is restored.

Before refreshing, confirm three conditions: the signer is connected by the original cable or paired wireless link; the companion console shows the device as unlocked; the host computer or phone has a stable connection. If any fails, fix that first. Also close other wallet programs that may claim the same USB or Bluetooth channel.

If no update control shows, the installed module already matches the vendor-signed release for your firmware. Do not force a reinstall to chase a phantom patch.

Never enter your recovery phrase anywhere.

When a refresh stalls, disconnect competing wallet programs, change the USB port or cable, restart the companion console, and retry. If the device screen freezes, wait for the operation to end, then unlock and check the module list. For persistent errors, consult the official support site; do not download replacement software from third-party mirrors.

Troubleshoot a Missing App or Failed Installation in Ledger Live

Reconnect the hardware wallet directly to the computer with its original cable, unlock the secure element, and reopen the Manager section; a dropped USB or Bluetooth link is the most common cause of a stalled coin-specific utility installation.

If the module stays absent, confirm the device firmware matches the minimum required by that utility, then check available storage on the secure element. Remove unused coin-specific binaries to free capacity, quit other wallet interfaces that may hold the USB channel, and retry from a wired connection without a hub. A failed signature or interrupted download usually clears after restarting the companion suite and clearing its cache from settings, but never bypass a device-screen confirmation.

When the utility is listed as unavailable rather than missing, verify the host operating system and companion build are current, because an outdated desktop or mobile client can hide compatible plugins from the catalogue. Use only the official download page; lookalike domains often distribute altered installers that fail signature checks. If installation reaches 100% but the module never appears on the device, disconnect, reboot the hardware wallet, and reconnect while the companion is open. Persistent failures point to a firmware mismatch, a damaged cable, or a blocked network path; test another port, another computer, and a different internet connection. For unresolved cases, export the diagnostic logs from the companion and contact official support through the channel listed in the software, never sharing the 24-word recovery phrase with anyone.

Remove Unused Ledger Apps to Free Device Storage

Uninstall dormant coin-specific modules through the official desktop or mobile companion; this releases secure-element capacity while leaving the recovery phrase, derived keys, and account history untouched.

Installed network programs occupy limited memory on the secure chip, and only a subset can remain available at once; the companion’s module area displays what is present and the remaining capacity. Open that section, connect, authenticate on the hardware, pick a blockchain utility you no longer use, choose the removal option, then confirm the action on the device screen. The flow does not ask for the 24-word backup, and a removed utility can be reinstalled later if you need to sign transactions for that network again.

Keep only the modules tied to assets you transact with regularly; removing a dormant program costs nothing, but restoring it takes a few minutes and a USB or Bluetooth link, so prune modules you rarely use instead of every seldom-used asset. Capacity varies by hardware model and firmware, and the companion reflects the current arrangement; check it after each removal to confirm that the freed space matches your expectation. This operation affects the secure element, not the computer’s disk, so deleting local wallet data or browser caches will not solve a full-chip message. If the device reports insufficient room during a future installation, repeat the same review, remove another unused utility, and confirm the change on the trusted screen; never enter your recovery phrase into the companion, a website, or a chat, because that phrase restores every derived key and cannot be replaced if exposed.

Questions & Answers:

What are the exact steps to install a new coin app in Ledger Live?

First, update Ledger Live and check whether your Ledger device firmware is current; back up your recovery phrase before making firmware changes. Connect the device with a reliable USB cable, or use Bluetooth only on supported models. Enter your PIN on the device to reach the dashboard, open Ledger Live, go to My Ledger, and confirm the manager/connection request on the device. In the app catalog, search for the exact asset name, such as Ethereum, Solana, or Bitcoin. Review the listing, select Install, and keep the device connected until Ledger Live reports completion. When it finishes, the app should appear on your device. For Bluetooth-capable models, pair the device first and keep it close to the computer or phone during installation.

Why is the app I want missing from the Ledger Live catalog?

The catalog is filtered by your Ledger device model and firmware version. If an app does not appear, update Ledger Live first, then update the device firmware if prompted. Reconnect the device, open My Ledger, and search for the exact app name. Some apps support only certain Ledger models or firmware versions, and a developer may pause or remove an app from the catalog. If it still does not show, check the provider’s official page for supported devices or contact Ledger support with your device model, firmware version, and Ledger Live version. Avoid installing random files from other websites as a workaround.

Do I have to update firmware before adding an app?

Usually, yes, if Ledger Live or the app listing says a firmware update is required. Firmware controls how apps are installed, how much storage is available, and which features the device supports. Before updating, write down your recovery phrase and keep it offline; never type it into a computer or website. Then connect the device, enter your PIN on the Ledger device to reach the dashboard, open Ledger Live, go to My Ledger, and follow the firmware update prompt. After the update, reconnect and install the app. If no update is offered, the app may still install normally. If installation fails after a firmware update, try another USB cable or port, or restart Ledger Live.

My app installation is stuck at “Processing” or fails. How should I fix it?

Check the basics first: use a direct USB port instead of a hub, use the cable that came with the device if possible, and make sure the device stays connected and you have entered your PIN to reach the dashboard. Close other wallet or manager programs that may be using the device. Restart Ledger Live and reconnect the device; enter your PIN on the device again to reach the dashboard. If the issue continues, clear the Ledger Live cache through Settings > Help > Clear cache and try once more. Confirm that the app name and device model are compatible and that firmware is current. If installation fails repeatedly, remove an unused app to free storage, or try another computer or phone. Keep your recovery phrase offline and never enter it during this troubleshooting.

Is it safe to install third-party apps in Ledger Live?

Ledger Live can show apps from Ledger and from external developers. Installing an app does not expose your recovery phrase or private keys; transactions still need approval on the Ledger screen. However, third-party apps are maintained by their providers, so confirm the app name and developer in the catalog and read the provider’s official documentation before using it. Avoid apps that promise recovery-phrase access or ask you to enter your recovery phrase. If an app requests suspicious permissions or a transaction you do not understand, reject it on the device and review the provider’s support page.

Ledger Live shows no app for my coin in My Ledger. What should I check before assuming the app is missing?

Check four things. First, make sure Ledger Live is current. Second, connect the Ledger by USB, enter the PIN, and open My Ledger. On the device, approve the manager request when prompted. Third, confirm your model and firmware support the app. A Nano S has less storage than a Nano X or Stax, so remove apps you do not use. Fourth, verify the coin or token is supported by an official Ledger app. Some tokens share a parent app, such as Ethereum for many EVM networks, so you may not see a separate app. If the app still does not appear, try another USB cable or port, restart Ledger Live and the device, and refresh the app list. For Bluetooth models, USB is often more reliable during app installation. If the app is listed but installation fails, check free space, close other wallet software that may be using the device, and try again. If all fails, contact Ledger support with your model, firmware version, Ledger Live version, and the exact error.

Can I add an app that is not in Ledger Live’s catalog, for example a custom token or a third-party app?

Ledger Live installs only apps signed and distributed by Ledger. You cannot load an unsigned app through the normal My Ledger flow. If a token is not in the catalog, it may still be covered by a broader app. For example, many EVM networks use the Ethereum app, and some other networks use a family app for several assets. Check the asset’s support page and the wallet you plan to pair with the Ledger. If the asset needs a separate app that Ledger does not offer, Ledger Live will not show it, and a third-party wallet cannot create that missing app on the device. Developer mode in Ledger Live may show test or developer apps for people building integrations, but it is not a way to install random apps. For everyday use, keep Ledger Live updated, use only official apps, and treat any sideloading method as unsupported.